Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing happened? Peek within the tank, and you might see no water inside. Before you panic, rest assured that repairing this problem is usually easy to accomplish. If you can’t figure it out yourself, you can always set up toilet repair with a knowledgeable plumber. Follow these guidelines to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first move is to make sure the water is turned on. If you or someone in your household recently did a toilet repair, you most likely turned off the water first. Did you forget to turn it back on? To find out, turn the water shut-off valve on the wall to the rear of the toilet. If the valve was shut, water ought to now start refilling the tank. If this fails to work, turn on the water at your sink or another plumbing fixture. If nothing spills out from the tap, you might have a larger water supply issue. Contact your water company to find out more. 

Reposition or Replace the Float Mechanism 

Older toilet brands use a float ball to gauge the water level as it increases in the tank. When the ball passes a specific height, the float arm it’s joined to stops the water flow. However, insufficient water could enter the tank if the ball is positioned incorrectly or the arm is broken. To correct the float ball, start by removing the toilet tank lid. Bend the float arm up a little to alter where it sits in the tank. If this does not fix the problem, you could need to replace the entire float mechanism. You should be able to complete this yourself by following the instructions that come with the replacement parts, or you can hire a plumber for help. Just note that float balls are old toilet design. You may prefer improved dependability and efficiency if you upgrade the existing tank components or replace the toilet completely. 

Adjust the Fill Valve 

Newer toilets utilize a float cup instead of a float ball, coupled with a fill valve and water level rod. There could quite possibly be no water in the toilet tank because the valve has slipped out of place or become clogged. Here are a few]] {tips to attempt: 

• Modify the fill valve: Have a look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly attached to the tube. Then, adjust the water level. More modern toilets have an adjustment knob you can turn manually, while older designs may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and allow the tank refill to test the water level. Adjust it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other crud could be covering the valve and preventing your toilet from filling. Turn off the water behind the toilet and remove the fill cap. Then, slowly turn the water back on, cupping your hand over the valve to stop water from spraying all over. After several seconds, turn the water back off. Finally, scrub the fill cap to clear away hard water buildup. If the cap is damaged, buy a new one. 
• Clean the valve tube: The tube below the fill valve might also be blocked. Shut off the water and take off the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on a little to flush away the junk. Replace the valve hardware and flush the toilet to check your adjustments. 

Repair or Replace the Trip Assembly 

If you’ve tried the steps above without any luck, the last possibility is a faulty trip assembly. This part links the flush handle to the tank. If it’s damaged or positioned poorly, the flush cycle may not complete, leaving the tank void. Detach the toilet tank lid and examine the trip assembly fastened to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or broken, replace it. Whether you complete the job yourself or leave it to a plumber, this simple repair should get your toilet tank filled with water once again. 

Schedule Toilet Repair Today 

You can’t go long without a reliable toilet, so reach out to [Company name] to inquire about a toilet repair. We can determine why your toilet isn’t filling and recommend the appropriate fix. If your plumbing fixture is older and worn out, our team can install a high-efficiency toilet in your home. Be assured that every plumbing repair and replacement we complete is backed by a 100% satisfaction guarantee. To schedule a visit from one of our licensed team members, please call your local Service Experts Heating, Air Conditioning & Plumbing office today.